Skip to content
Related Articles

Related Articles

Improve Article

Packet Switching and Delays in Computer Network

  • Difficulty Level : Hard
  • Last Updated : 18 Oct, 2021
Geek Week

Packet switching is a method of transferring the data to a network in form of packets. In order to transfer the file fast and efficiently manner over the network and minimize the transmission latency, the data is broken into small pieces of variable length, called Packet. At the destination, all these small parts (packets) have to be reassembled, belonging to the same file. A packet composes of payload and various control information. No pre-setup or reservation of resources is needed. 

Packet Switching uses Store and Forward technique while switching the packets; while forwarding the packet each hop first stores that packet then forward. This technique is very beneficial because packets may get discarded at any hop due to some reason. More than one path is possible between a pair of sources and destinations. Each packet contains Source and destination address using which they independently travel through the network. In other words, packets belonging to the same file may or may not travel through the same path. If there is congestion at some path, packets are allowed to choose different paths possible over an existing network. 

Packet-Switched networks were designed to overcome the weaknesses of Circuit-Switched networks since circuit-switched networks were not very effective for small messages. 

Advantage of Packet Switching over Circuit Switching : 
 

  • More efficient in terms of bandwidth, since the concept of reserving circuit is not there.
  • Minimal transmission latency.
  • More reliable as a destination can detect the missing packet.
  • More fault tolerant because packets may follow a different path in case any link is down, Unlike Circuit Switching.
  • Cost-effective and comparatively cheaper to implement.

The disadvantage of Packet Switching over Circuit Switching : 
 



  • Packet Switching doesn’t give packets in order, whereas Circuit Switching provides ordered delivery of packets because all the packets follow the same path.
  • Since the packets are unordered, we need to provide sequence numbers for each packet.
  • Complexity is more at each node because of the facility to follow multiple paths.
  • Transmission delay is more because of rerouting.
  • Packet Switching is beneficial only for small messages, but for bursty data (large messages) Circuit Switching is better.

Modes of Packet Switching : 
 

1. Connection-oriented Packet Switching (Virtual Circuit) : 
Before starting the transmission, it establishes a logical path or virtual connection using signaling protocol, between sender and receiver and all packets belongs to this flow will follow this predefined route. Virtual Circuit ID is provided by switches/routers to uniquely identify this virtual connection. Data is divided into small units and all these small units are appended with help of sequence numbers. Overall, three phases take place here- The setup, data transfer and tear down phase. 
 

All address information is only transferred during the setup phase. Once the route to a destination is discovered, entry is added to the switching table of each intermediate node. During data transfer, packet header (local header) may contain information such as length, timestamp, sequence number, etc. 
Connection-oriented switching is very useful in switched WAN. Some popular protocols which use the Virtual Circuit Switching approach are X.25, Frame-Relay, ATM, and MPLS(Multi-Protocol Label Switching).

2. Connectionless Packet Switching (Datagram) :
Unlike Connection-oriented packet switching, In Connectionless Packet Switching each packet contains all necessary addressing information such as source address, destination address and port numbers, etc. In Datagram Packet Switching, each packet is treated independently. Packets belonging to one flow may take different routes because routing decisions are made dynamically, so the packets arrived at the destination might be out of order. It has no connection setup and teardown phase, like Virtual Circuits. 
Packet delivery is not guaranteed in connectionless packet switching, so reliable delivery must be provided by end systems using additional protocols. 
 

 

A---R1---R2---B

A is the sender (start)
R1, R2 are two routers that store and forward data
B is receiver(destination)

To send a packet from A to B there are delays since this is a Store and Forward network. 

Delays in Packet switching :

  1. Transmission Delay
  2. Propagation Delay
  3. Queuing Delay
  4. Processing Delay

Attention reader! Don’t stop learning now.  Practice GATE exam well before the actual exam with the subject-wise and overall quizzes available in GATE Test Series Course.

Learn all GATE CS concepts with Free Live Classes on our youtube channel.

My Personal Notes arrow_drop_up
Recommended Articles
Page :