Why Selective Repeat Protocol?
The go-back-n protocol works well if errors are less, but if the line is poor it wastes a lot of bandwidth on retransmitted frames. An alternative strategy, the selective repeat protocol, is to allow the receiver to accept and buffer the frames following a damaged or lost one.
Selective Repeat attempts to retransmit only those packets that are actually lost (due to errors) :
- Receiver must be able to accept packets out of order.
- Since receiver must release packets to higher layer in order, the receiver must be able to buffer some packets.
Retransmission requests :
- Implicit – The receiver acknowledges every good packet, packets that are not ACKed before a time-out are assumed lost or in error.Notice that this approach must be used to be sure that every packet is eventually received.
- Explicit – An explicit NAK (selective reject) can request retransmission of just one packet. This approach can expedite the retransmission but is not strictly needed.
- One or both approaches are used in practice.
Selective Repeat Protocol (SRP) :
This protocol(SRP) is mostly identical to GBN protocol, except that buffers are used and the receiver, and the sender, each maintain a window of size. SRP works better when the link is very unreliable. Because in this case, retransmission tends to happen more frequently, selectively retransmitting frames is more efficient than retransmitting all of them. SRP also requires full duplex link. backward acknowledgements are also in progress.
- Sender’s Windows ( Ws) = Receiver’s Windows ( Wr).
- Window size should be less than or equal to half the sequence number in SR protocol. This is to avoid packets being recognized incorrectly. If the windows size is greater than half the sequence number space, then if an ACK is lost, the sender may send new packets that the receiver believes are retransmissions.
- Sender can transmit new packets as long as their number is with W of all unACKed packets.
- Sender retransmit un-ACKed packets after a timeout – Or upon a NAK if NAK is employed.
- Receiver ACKs all correct packets.
- Receiver stores correct packets until they can be delivered in order to the higher layer.
- In Selective Repeat ARQ, the size of the sender and receiver window must be at most one-half of 2^m.
Efficiency of Selective Repeat Protocol (SRP) is same as GO-Back-N’s efficiency :
Efficiency = N/(1+2a) Where a = Propagation delay / Transmission delay Buffers = N + N Sequence number = N(sender side) + N ( Receiver Side)
This article is contributed by Akash Sharan. If you like GeeksforGeeks and would like to contribute, you can also write an article using contribute.geeksforgeeks.org or mail your article to email@example.com. See your article appearing on the GeeksforGeeks main page and help other Geeks.
Please write comments if you find anything incorrect, or you want to share more information about the topic discussed above.
Attention reader! Don’t stop learning now. Get hold of all the important CS Theory concepts for SDE interviews with the CS Theory Course at a student-friendly price and become industry ready.
- Difference between Stop and Wait protocol and Sliding Window protocol
- Difference Between Go-Back-N and Selective Repeat Protocol
- Sliding Window Protocol | Set 1 (Sender Side)
- Sliding Window Protocol | Set 2 (Receiver Side)
- Difference between Stop and Wait, GoBackN and Selective Repeat
- Sliding Window protocols Summary With Questions
- Hot Standby Router Protocol (HSRP) and Virtual Router Redundancy Protocol (VRRP)
- Difference between File Transfer Protocol (FTP) and Secure File Transfer Protocol (SFTP)
- Difference between Serial Line Internet Protocol (SLIP) and Point-to-Point Protocol (PPP)
- Cisco Discovery Protocol (CDP) and Link Layer Discovery Protocol (LLDP) in Data Link Layer
- Difference between Border Gateway Protocol (BGP) and Routing Information Protocol (RIP)
- Selective forwarding Attack in wireless Sensor Network
- What is ARQ (Automatic Repeat Request)?
- Two Phase Locking (2-PL) Concurrency Control Protocol | Set 3
- Secure Electronic Transaction (SET) Protocol
- Internet Control Message Protocol (ICMP)
- Simple Mail Transfer Protocol (SMTP)
- Program to remotely Power On a PC over the internet using the Wake-on-LAN protocol.
- Internet Protocol version 6 (IPv6)
- Internet Protocol version 6 (IPv6) Header