Skip to content
Related Articles

Related Articles

Mark-and-Sweep: Garbage Collection Algorithm

View Discussion
Improve Article
Save Article
Like Article
  • Difficulty Level : Medium
  • Last Updated : 10 May, 2022

There are many garbage collection algorithms that run in the background, of which one of them is mark and sweep.

All the objects which are created dynamically (using new in C++ and Java) are allocated memory in the heap. If we go on creating objects we might get Out Of Memory error since it is not possible to allocate heap memory to objects. So we need to clear heap memory by releasing memory for all those objects which are no longer referenced by the program (or the unreachable objects) so that the space is made available for subsequent new objects. This memory can be released by the programmer itself but it seems to be an overhead for the programmer, here garbage collection comes to our rescue, and it automatically releases the heap memory for all the unreferenced objects. 

Mark and Sweep Algorithm 

Any garbage collection algorithm must perform 2 basic operations. One, it should be able to detect all the unreachable objects and secondly, it must reclaim the heap space used by the garbage objects and make the space available again to the program. The above operations are performed by Mark and Sweep Algorithm in two phases as listed and described further as follows: 

  • Mark phase
  • Sweep phase

Phase 1: Mark Phase 

When an object is created, its mark bit is set to 0(false). In the Mark phase, we set the marked bit for all the reachable objects (or the objects which a user can refer to) to 1(true). Now to perform this operation we simply need to do a graph traversal, a depth-first search approach would work for us. Here we can consider every object as a node and then all the nodes (objects) that are reachable from this node (object) are visited and it goes on till we have visited all the reachable nodes.

  • The root is a variable that refers to an object and is directly accessible by a local variable. We will assume that we have one root only.
  • We can access the mark bit for an object by ‘markedBit(obj)’.

Algorithm: Mark phase 

Mark(root)
If markedBit(root) = false then
                     markedBit(root) = true
                                       For each v referenced by root
                                       Mark(v)

Note: If we have more than one root, then we simply have to call Mark() for all the root variables. 

Phase 2: Sweep Phase 

As the name suggests it “sweeps” the unreachable objects i.e. it clears the heap memory for all the unreachable objects. All those objects whose marked value is set to false are cleared from the heap memory, for all other objects (reachable objects) the marked bit is set to true. 
Now the mark value for all the reachable objects is set to false since we will run the algorithm (if required) and again we will go through the mark phase to mark all the reachable objects. 

Algorithm: Sweep Phase 

Sweep()
For each object p in heap
If markedBit(p) = true then
                  markedBit(p) = false
                                 else
                                     heap.release(p)

The mark-and-sweep algorithm is called a tracing garbage collector because it traces out the entire collection of objects that are directly or indirectly accessible by the program. 

Example: 

A. All the objects have their marked bits set to false. 
 

M&S_Fig1

B. Reachable objects are marked true

M&S_Fig2

C. Nonreachable objects are cleared from the heap. 

 

M&S_Fig3

Advantages of Mark and Sweep Algorithm are as follows: 

  • It handles the case with cyclic references, even in the case of a cycle, this algorithm never ends up in an infinite loop.
  • There are no additional overheads incurred during the execution of the algorithm.

Disadvantages of the Mark and Sweep Algorithm are as follows:

  • The main disadvantage of the mark-and-sweep approach is the fact that  normal program execution is suspended while the garbage collection algorithm runs.
  • Another disadvantage is that, after the Mark and Sweep Algorithm is run several times on a program, reachable objects end up being separated by many, small unused memory regions. Look at the below figure for a better understanding. 

HeapMemory

Here white blocks denote the free memory, while the grey blocks denote the memory taken by all the reachable objects. 

Now the free segments (which are denoted by white color) are of varying sizes let’s say the 5 free segments are of size 1, 1, 2, 3, 5 (size in units). 
Now we need to create an object which takes 10 units of memory, now assuming that memory can be allocated only in the contiguous form of blocks, the creation of an object is not possible although we have an available memory space of 12 units and it will cause OutOfMemory error

This problem is termed “Fragmentation”. We have memory available in “fragments” but we are unable to utilize that memory space. We can reduce the fragmentation by compaction; we shuffle the memory content to place all the free memory blocks together to form one large block. Now consider the above example, after compaction we have a contiguous block of free memory of size 12 units so now we can allocate memory to an object of size 10 units. 

This article is contributed by Chirag Agarwal. If you like GeeksforGeeks and would like to contribute, you can also write an article and mail your article to review-team@geeksforgeeks.org. See your article appearing on the GeeksforGeeks main page and help other Geeks. Please write comments if you find anything incorrect, or you want to share more information about the topic discussed above.

My Personal Notes arrow_drop_up
Recommended Articles
Page :

Start Your Coding Journey Now!