Please refer this as a prerequisite article: Sliding Window Protocol (sender side)| set 1
Sliding Window Protocol is actually a theoretical concept in which we have only talked about what should be the sender window size (1+2a) in order to increase the efficiency of stop and wait arq. Now we will talk about the practical implementations in which we take care of what should be the size of receiver window. Practically it is implemented in two protocols namely :
- Go Back N (GBN)
- Selective Repeat (SR)
In this article, we will explain you about the first protocol which is GBN in terms of three main characteristic features and in the next part we will be discussing SR as well as comparison of both these protocols
Go Back N (GBN) Protocol
The three main characteristic features of GBN are:
- Sender Window Size (WS)
It is N itself. If we say the protocol is GB10, then Ws = 10. N should be always greater than 1 in order to implement pipelining. For N = 1, it reduces to Stop and Wait protocol.
Efficiency Of GBN = N/(1+2a) where a = Tp/Tt
If B is the bandwidth of the channel, then
Effective Bandwidth or Throughput = Efficiency * Bandwidth = (N/(1+2a)) * B
- Receiver Window Size (WR)
WR is always 1 in GBN.
Now what exactly happens in GBN, we will explain with a help of example. Consider the diagram given below. We have sender window size of 4. Assume that we have lots of sequence numbers just for the sake of explanation. Now the sender has sent the packets 0, 1, 2 and 3. After acknowledging the packets 0 and 1, receiver is now expecting packet 2 and sender window has also slided to further transmit the packets 4 and 5. Now suppose the packet 2 is lost in the network, Receiver will discard all the packets which sender has transmitted after packet 2 as it is expecting sequence number of 2. On the sender side for every packet send there is a time out timer which will expire for packet number 2. Now from the last transmitted packet 5 sender will go back to the packet number 2 in the current window and transmit all the packets till packet number 5. That’s why it is called Go Back N. Go back means sender has to go back N places from the last transmitted packet in the unacknowledged window and not from the point where the packet is lost.
There are 2 kinds of acknowledgements namely:
- Cumulative Ack: One acknowledgement is used for many packets. The main advantage is traffic is less. A disadvantage is less reliability as if one ack is the loss that would mean that all the packets sent are lost.
- Independent Ack: If every packet is going to get acknowledgement independently. Reliability is high here but a disadvantage is that traffic is also high since for every packet we are receiving independent ack.
GBN uses Cumulative Acknowledgement. At the receiver side, it starts a acknowledgement timer whenever receiver receives any packet which is fixed and when it expires, it is going to send a cumulative Ack for the number of packets received in that interval of timer. If receiver has received N packets, then the Acknowledgement number will be N+1. Important point is Acknowledgement timer will not start after the expiry of first timer but after receiver has received a packet.
Time out timer at the sender side should be greater than Acknowledgement timer.
Relationship Between Window Sizes and Sequence Numbers
We already know that sequence numbers required should always be equal to the size of window in any sliding window protocol.
Minimum sequence numbers required in GBN = N + 1
Bits Required in GBN = ceil(log2 (N + 1)) The extra 1 is required in order to avoid the problem of duplicate packets as described below.
Example: Consider an example of GB4.
- Sender window size is 4 therefore we require a minimum of 4 sequence numbers to label each packet in the window.
- Now suppose receiver has received all the packets(0, 1, 2 and 3 sent by sender) and hence is now waiting for packet number 0 again (We can not use 4 here as we have only 4 sequence numbers available since N = 4).
- Now suppose the cumulative ack for the above 4 packets is lost in the network.
- On sender side, there will be timeout for packet 0 and hence all the 4 packets will be transmitted again.
- Problem now is receiver is waiting for new set of packets which should have started from 0 but now it will receive the duplicate copies of the previously accepted packets.
- In order to avoid this, we need one extra sequence number.
- Now the receiver could easily reject all the duplicate packets which were starting from 0 because now it will be waiting for packet number 4 (We have added an extra sequence number now).
This is explained with the help of the illustrations below.
Trying with Sequence numbers 4.
Now Trying with one extra Sequence Number.
Now it is clear as to why we need an extra 1 bit in the GBN protocol.
In the next article, we will explain Selective repeat and comparison between the 2 protocols.
This article is contributed by Pranjul Ahuja. If you like GeeksforGeeks and would like to contribute, you can also write an article using contribute.geeksforgeeks.org or mail your article to firstname.lastname@example.org. See your article appearing on the GeeksforGeeks main page and help other Geeks.
Please write comments if you find anything incorrect, or you want to share more information about the topic discussed above.
Attention reader! Don’t stop learning now. Get hold of all the important CS Theory concepts for SDE interviews with the CS Theory Course at a student-friendly price and become industry ready.
- Sliding Window Protocol | Set 1 (Sender Side)
- Difference between Stop and Wait protocol and Sliding Window protocol
- Sliding Window Protocol | Set 3 (Selective Repeat)
- Rake Receiver
- Sliding Window protocols Summary With Questions
- Hot Standby Router Protocol (HSRP) and Virtual Router Redundancy Protocol (VRRP)
- Difference between File Transfer Protocol (FTP) and Secure File Transfer Protocol (SFTP)
- Difference between Serial Line Internet Protocol (SLIP) and Point-to-Point Protocol (PPP)
- Cisco Discovery Protocol (CDP) and Link Layer Discovery Protocol (LLDP) in Data Link Layer
- Difference between Border Gateway Protocol (BGP) and Routing Information Protocol (RIP)
- Secure Electronic Transaction (SET) Protocol
- Internet Control Message Protocol (ICMP)
- Simple Mail Transfer Protocol (SMTP)
- Program to remotely Power On a PC over the internet using the Wake-on-LAN protocol.
- Internet Protocol version 6 (IPv6)
- Internet Protocol version 6 (IPv6) Header
- File Transfer Protocol (FTP) in Application Layer
- How Address Resolution Protocol (ARP) works?
- User Datagram Protocol (UDP)
- Distance Vector Routing (DVR) Protocol