Prerequisite – Open shortest path first (OSPF)
Open shortest path first (OSPF) is a link-state routing protocol which is used to find the best path between the source and the destination router using its own SPF algorithm.
Open shortest path first (OSPF) router roles –
An area is a group of contiguous network and routers. Routers belonging to same area shares a common topology table and area I’d. The area I’d is associated with router’s interface as a router can belong to more than one area. There are some roles of router in OSPF:
- Backbone router – The area 0 is known as backbone area and the routers in area 0 are known as backbone routers. If the routers exists partially in the area 0then also it is a backbone router.
- Internal router – An internal router is a router which have all of its interfaces in a single area.
- Area Boundary Router (ABR) – The router which connects backbone area with another area is called Area Boundary Router. It belongs to more than one area. The ABRs therefore maintain multiple link-state databases that describe both the backbone topology and the topology of the other areas.
- 4.Area Summary Border Router (ASBR) – When an OSPF router is connected to a different protocol like EIGRP, or Border Gateway Protocol, or any other routing protocol then it is known as AS. The router which connects two different AS (in which one of the interface is operating OSPF) is known as Area Summary Border Router. These routers perform redistribution. ASBRs run both OSPF and another routing protocol, such as RIP or BGP. ASBRs advertise the exchanged external routing information throughout their AS.
Note – A router can be backbone router and Area Boundary Router at the same time i.e a router can perform more than one role at a time.
There is a small topology in which there are 3 routers namely R1, R2, R3 are connected. R1 is connected to networks 10.255.255.80/30 (interface fa0/1), 192.168.10.48/29 (interface fa0/0) and 10.255.255.8/30 (interface gi0/0)
Note – In the figure, IP addresses are written with their respected interfaces but as have to advertise networks therefore, you have to write network I’d. R2 is connected to networks 192.168.10.64/29 (interface fa0/0), 10.255.255.80/30 (interface fa0/1). R3 is connected to networks 10.255.255.8/30 (int fa0/1), 192.168.10.16/29 (int fa0/0).
Now, configuring OSPF for R1.
R1(config)#router ospf 1 R1(config-router)#network 192.168.10.48 0.0.0.7 area 1 R1(config-router)#network 10.255.255.80 0.0.0.3 area 1 R1(config-router)#network 10.255.255.8 0.0.0.3 area 1
Here, 1 is the OSPF instance or process I’d. It can be same or different (doesn’t matter). You have use wildcard mask here and area used is 1.
Now, configuring R2
R2(config)#router ospf 1 R2(config-router)#network 192.168.10.64 0.0.0.7 area 1 R2(config-router)#network 10.255.255.80 0.0.0.3 area 1
Similarly, for R3
R3(config)#router ospf 1 R3(config-router)#network 192.168.10.16 0.0.0.7 area 1 R3(config-router)#network 10.255.255.8 0.0.0.3 area 1
You can check the configuration by typing command
R3#show ip protocols
Don’t stop now and take your learning to the next level. Learn all the important concepts of Data Structures and Algorithms with the help of the most trusted course: DSA Self Paced. Become industry ready at a student-friendly price.
- Open shortest path first (OSPF) - Set 2
- Open Shortest Path First (OSPF) protocol States
- Open Shortest Path First (OSPF) Protocol fundamentals
- Configuration of Router on a stick
- Introduction of Virtual Router Redundancy Protocol (VRRP) and its configuration
- Probabilistic shortest path routing algorithm for optical networks
- Hot Standby Router Protocol (HSRP) and Virtual Router Redundancy Protocol (VRRP)
- Difference between OSPF and BGP
- Difference between RIP and OSPF
- Difference between EIGRP and OSPF
- Difference between OSPF and IGRP
- Difference between Router and Hub
- Introduction of a Router
- Difference between Router and Firewall
- Difference between Router and Switch
- Cisco Router modes
- Difference between Modem and Router
- Difference between Bridge and Router
- Difference between Router and Gateway
- EIGRP Configuration
If you like GeeksforGeeks and would like to contribute, you can also write an article using contribute.geeksforgeeks.org or mail your article to email@example.com. See your article appearing on the GeeksforGeeks main page and help other Geeks.
Please Improve this article if you find anything incorrect by clicking on the "Improve Article" button below.