VRRP is an open standard protocol, which is used to provide redundancy in a network. It is a network layer protocol (protocol number-112).
The number of routers (group members) in a group acts as a virtual logical router which will be the default gateway of all the local hosts. If one router goes down, one of the other group members can take place for the responsibilities for forwarding the traffic.
Some important terms related to VRRP :
- virtual IP address : An IP address is assigned as a virtual IP address from the local subnet which is configured as a default gateway for all the local hosts.
- Virtual MAC address : A virtual MAC address is automatically generated by taking the last 8 bytes as the VRRP group number in hexadecimal. In VRRP, Mac address used is 0000.5e00.01xx. Here, xx is the VRRP group number in hexadecimal.
- Master router : One of the VRRP group member is elected as master router which takes up the responsibility of forwarding the local traffic. The router is elected on the basis of priority. If some group member of VRRP group has higher priority than others then it will be elected as master router. If the priority is same(by default 100) then the router having the highest IP address will become the master router.
- Backup routers : Only one of the VRRP group member will become the master router while others will be back up routers. In case the master router fails then one of the backup routers will become master router.
- Master advertisement timer : The master router multicast the keep-alive messages at 220.127.116.11 in every 1 second.
- Master dead timer : The time in which the backup router will take up the responsibilities of Master router if the master advertisement message is not received. It is, by default, 3.69 seconds.
- Prempt : It is a state in which one of the backup routers become the master router (when the master router goes down). Also, when the master router comes up again, it will become the master router as it’s priority is still higher.
- Object tracking : The VRRP object tracking provides a way in which the best router will become the master router. The current master router continuously polls the tracked object state (such as line protocol is up or down). Suppose if the master router line protocol is down then the priority of backup router will be increased dynamically i.e it will become the master router.
VRRP supports 3 types of authentication –
1. No authentication
2. Plain text authentication
3. MD5 authentication
VRRP rejects packet in any of the following cases :
1. The authentication schemes differ on the routers and the incoming packet.
2. MD5 digest differs on the router and the incoming packet.
3. Text authentication strings are different on the router and the incoming packet.
In above given topology, there are 2-routers named R1 and R2, where R1 fa 0/0 ip address is 10.1.1.1/24 and R2 fa0/0 ip address is 10.1.1.2/24.
Assigning IP address to router R1 :
r1# int fa0/0 r1# ip add 10.1.1.1 255.255.255.0
Assigning IP address to router r2.
r2# int fa0/0 r2# ip address 10.1.1.2 255.255.255.0
Now, let’s provide virtual IP address(10.1.1.100), group name VRRP_TEST, group number 10 and priority 110. Also, here preempt has been enabled by default i.e. if the master router goes down then the backup router automatically becomes the master router.
r1# int fa0/0 r1# vrrp 10 ip 10.1.1.100 r1# vrrp 10 name VRRP_TEST r1# vrrp 10 priority 110
Now, provide virtual IP address(10.1.1.100), group name VRRP_TEST and priority 100. Also, group number 10 is assigned.
r2# int fa0/0 r2# vrrp 10 ip 10.1.1.100 r2# vrrp 10 name VRRP_TEST r2# vrrp 10 priority 100
Note : As provided priority 110 to r1, therefore, it will become the master router.
Attention reader! Don’t stop learning now. Get hold of all the important CS Theory concepts for SDE interviews with the CS Theory Course at a student-friendly price and become industry ready.
- Hot Standby Router Protocol (HSRP) and Virtual Router Redundancy Protocol (VRRP)
- Open shortest path first (OSPF) router roles and configuration
- Configuration of Router on a stick
- Hot Standby Router Protocol (HSRP)
- Dynamic Host Configuration Protocol (DHCP)
- Working of Dynamic Host Configuration Protocol
- Difference between Stop and Wait protocol and Sliding Window protocol
- Cyclic Redundancy Check in Python
- Vertical Redundancy Check (VRC) or Parity Check
- Longitudinal Redundancy Check (LRC)/2-D Parity Check
- Difference between File Transfer Protocol (FTP) and Secure File Transfer Protocol (SFTP)
- Difference between Serial Line Internet Protocol (SLIP) and Point-to-Point Protocol (PPP)
- Cisco Discovery Protocol (CDP) and Link Layer Discovery Protocol (LLDP) in Data Link Layer
- Difference between Border Gateway Protocol (BGP) and Routing Information Protocol (RIP)
- Introduction of a Router
- Difference between Virtual Private Network (VPN) and Multi-Protocol Label Switching (MPLS)
- Stop and Wait protocol, its problems and solutions
- Difference between Modem and Router
- Difference between Router and Switch
- Difference between Bridge and Router
If you like GeeksforGeeks and would like to contribute, you can also write an article using contribute.geeksforgeeks.org or mail your article to email@example.com. See your article appearing on the GeeksforGeeks main page and help other Geeks.
Please Improve this article if you find anything incorrect by clicking on the "Improve Article" button below.