Prerequisite – Flag register in 8085 microprocessor
The Flag register is a Special Purpose Register. Depending upon the value of result after any arithmetic and logical operation the flag bits become set (1) or reset (0).
Figure – Format of flag register
There are total 9 flags in 8086 and the flag register is divided into two types:
(a) Status Flags – There are 6 flag registers in 8086 microprocessor which become set(1) or reset(0) depending upon condition after either 8-bit or 16-bit operation. These flags are conditional/status flags. 5 of these flags are same as in case of 8085 microprocessor and their working is also same as in 8085 microprocessor. The sixth one is the overflow flag.
The 6 status flags are:
- Sign Flag (S)
- Zero Flag (Z)
- Auxiliary Cary Flag (AC)
- Parity Flag (P)
- Carry Flag (CY)
These first five flags are defined here
- Overflow Flag (O) – This flag will be set (1) if the result of a signed operation is too large to fit in the number of bits available to represent it, otherwise reset (0). After any operation, if D generates any carry and passes to D OR if D does not generates carry but D generates, overflow flag becomes set, i.e., 1. If D and D both generate carry or both do not generate any carry, then overflow flag becomes reset, i.e., 0.
Example: On adding bytes 100 + 50 (result is not in range -128…127), so overflow flag will set.
MOV AL, 50 (50 is 01010000 which is positive) MOV BL, 32 (32 is 00110010 which is positive) ADD AL, BL (82 is 10000010 which is negative)
Overflow flag became set as we added 2 +ve numbers and we got a -ve number.
(b) Control Flags – The control flags enable or disable certain operations of the microprocessor. There are 3 control flags in 8086 microprocessor and these are:
- Directional Flag (D) – This flag is specifically used in string instructions.
If directional flag is set (1), then access the string data from higher memory location towards lower memory location.
If directional flag is reset (0), then access the string data from lower memory location towards higher memory location.
- Interrupt Flag (I) – This flag is for interrupts.
If interrupt flag is set (1), the microprocessor will recognize interrupt requests from the peripherals.
If interrupt flag is reset (0), the microprocessor will not recognize any interrupt requests and will ignore them.
- Trap Flag (T) – This flag is used for on-chip debugging. Setting trap flag puts the microprocessor into single step mode for debugging. In single stepping, the microprocessor executes a instruction and enters into single step ISR.
If trap flag is set (1), the CPU automatically generates an internal interrupt after each instruction, allowing a program to be inspected as it executes instruction by instruction.
If trap flag is reset (0), no function is performed.
Attention reader! Don’t stop learning now. Get hold of all the important CS Theory concepts for SDE interviews with the CS Theory Course at a student-friendly price and become industry ready.
- 8085 program to access and exchange the content of Flag register with register B
- Flag register in 8085 microprocessor
- 8085 program to exchange content of HL register pair with DE register pair
- Difference between Register Mode and Register Indirect Mode
- 8085 program to find 2's complement of the contents of Flag Register
- Register content and Flag status after Instructions
- General purpose registers in 8086 microprocessor
- Arithmetic instructions in 8086 microprocessor
- Logical instructions in 8086 microprocessor
- Data transfer instructions in 8086 microprocessor
- Reset Accumulator (8085 & 8086 microprocessor)
- Process control instructions in 8086 microprocessor
- Memory Segmentation in 8086 Microprocessor
- Differences between 8085 and 8086 microprocessor
- Addressing modes in 8086 microprocessor
- String manipulation instructions in 8086 microprocessor
- Program execution transfer instructions in 8086 microprocessor
- Pin diagram of 8086 microprocessor
- Interrupts in 8086 microprocessor
- Bus Cycles of 8086 Microprocessor
If you like GeeksforGeeks and would like to contribute, you can also write an article using contribute.geeksforgeeks.org or mail your article to email@example.com. See your article appearing on the GeeksforGeeks main page and help other Geeks.
Please Improve this article if you find anything incorrect by clicking on the "Improve Article" button below.
Improved By : Shivi_Aggarwal