Skip to content
Related Articles
Open in App
Not now

Related Articles

Ethernet Frame Format

Improve Article
Save Article
  • Difficulty Level : Medium
  • Last Updated : 06 Oct, 2022
Improve Article
Save Article

Prerequisite – Introduction to Ethernet Basic frame format which is required for all MAC implementation is defined in IEEE 802.3 standard. Though several optional formats are being used to extend the protocol’s basic capability. Ethernet frame starts with Preamble and SFD, both works at the physical layer. Ethernet header contains both Source and Destination MAC address, after which the payload of the frame is present. The last field is CRC which is used to detect the error. Now, let’s study each field of basic frame format.

Ethernet (IEEE 802.3) Frame Format –

  • PREAMBLE – Ethernet frame starts with 7-Bytes Preamble. This is a pattern of alternative 0’s and 1’s which indicates starting of the frame and allow sender and receiver to establish bit synchronization. Initially, PRE (Preamble) was introduced to allow for the loss of a few bits due to signal delays. But today’s high-speed Ethernet don’t need Preamble to protect the frame bits. PRE (Preamble) indicates the receiver that frame is coming and allow the receiver to lock onto the data stream before the actual frame begins.
  • Start of frame delimiter (SFD) – This is a 1-Byte field which is always set to 10101011. SFD indicates that upcoming bits are starting of the frame, which is the destination address. Sometimes SFD is considered the part of PRE, this is the reason Preamble is described as 8 Bytes in many places. The SFD warns station or stations that this is the last chance for synchronization.
  • Destination Address – This is 6-Byte field which contains the MAC address of machine for which data is destined.
  • Source Address – This is a 6-Byte field which contains the MAC address of source machine. As Source Address is always an individual address (Unicast), the least significant bit of first byte is always 0.
  • Length – Length is a 2-Byte field, which indicates the length of entire Ethernet frame. This 16-bit field can hold the length value between 0 to 65534, but length cannot be larger than 1500 Bytes because of some own limitations of Ethernet.
  • Data – This is the place where actual data is inserted, also known as Payload. Both IP header and data will be inserted here if Internet Protocol is used over Ethernet. The maximum data present may be as long as 1500 Bytes. In case data length is less than minimum length i.e. 46 bytes, then padding 0’s is added to meet the minimum possible length.
  • Cyclic Redundancy Check (CRC) – CRC is 4 Byte field. This field contains a 32-bits hash code of data, which is generated over the Destination Address, Source Address, Length, and Data field. If the checksum computed by destination is not the same as sent checksum value, data received is corrupted.

Note – Size of frame of Ethernet IEEE 802.3 varies 64 bytes to 1518 bytes including data length (46 to 1500 bytes).

Brief overview on Extended Ethernet Frame (Ethernet II Frame) :

Standard IEEE 802.3 basic frame format is discussed above in detail. Now let’s see the extended Ethernet frame header, using which we can get Payload even larger than 1500 Bytes. DA [Destination MAC Address] : 6 bytes SA [Source MAC Address] : 6 bytes Type [0x8870 (Ethertype)] : 2 bytes DSAP [802.2 Destination Service Access Point] : 1 byte SSAP [802.2 Source Service Access Point] : 1 byte Ctrl [802.2 Control Field] : 1 byte Data [Protocol Data] : > 46 bytes FCS [Frame Checksum] : 4 bytes Although length field is missing in Ethernet II frame, the frame length is known by virtue of the frame being accepted by the network interface. GATE CS Corner Questions Practicing the following questions will help you test your knowledge. All questions have been asked in GATE in previous years or in GATE Mock Tests. It is highly recommended that you practice them.

  1. GATE CS 2007, Question 85
  2. GATE CS 2005, Question 74
  3. GATE CS 2004, Question 90
  4. GATE IT 2005, Question 27
  5. GATE CS 2016 (Set 2), Question 34

References – Extended Ethernet Frame Size Support ciscopress IEEE 802.3 and Ethernet This article is contributed by Abhishek Agrawal. If you like GeeksforGeeks and would like to contribute, you can also write an article using or mail your article to See your article appearing on the GeeksforGeeks main page and help other Geeks. Please write comments if you find anything incorrect, or you want to share more information about the topic discussed above.

My Personal Notes arrow_drop_up
Related Articles

Start Your Coding Journey Now!