A router is a layer 3 device used to forward packet from one network to another. It forwards the packet through one of its port on the basis of destination IP address and the entry in the routing table. By using routing table, it finds an optimised path between the source and destination network.
Here, we will talk about Cisco router basic commands like assigning IP address to an interface, bringing up an interface, applying enable and secret password.
Giving hostname to router –
It is used to set a name to a device stating an identity to a device. This is important as these hostname are used in WAN for authentication purpose.
We can set the hostname as:
router(config)#hostname GeeksforGeeksrouter GeeksforGeeksrouter(config)#
Applying banner – These are specifically used to give a small security notice to the user who wants to access the router. We can customize it According to our need as like asking for credentials needed for the login.
Types of banner are:
- banner motd –
GeeksforGeeksrouter(config)#banner motd # Enter Text message. End with character '#' $ No unauthorised access allowed. Enter your credentials!! #
Here motd means message of the day and # means delimiter i.e message should end with the symbol provided. This message will be shown while entering into the router’s user execution mode
- Exec banner – It will be displayed on the screen when the user will login through the VTY lines.
- Login banner – This banner will be displayed after the banner motd but before the login.
These banners are used to make login interactive.
Setting password –
There are five passwords used to secure a cisco device:
- enable password – The enable password is used for securing privilege mode. This password will be shown in clear text by command “show running-configuration”. These are replaced by secret password nowadays.
router(config)#enable password GeeksforGeeks
- Enable secret password – This is also used for securing privilege mode but the d the difference is that it will be displayed as cipher in “show running-configuration”. This password will override the enable password if both passwords are set.
router(config)#enable secret GeeksforGeeks
- line console password – When a user will take access through console port then this password will be asked.
router(config)#line console 0 router(config-line)#password GeeksforGeeks router(config-line)#login
- line VTY password – When a user want to access a router through VTY lines (telnet or ssh) then this password will be asked.
Following configuration is shown for telnet password.
router(config)#line VTY 0 4 router(config-line)#password GeeksforGeeks router(config-line)#exit
- auxiliary password – This password will secure the aux port.
router(config)#line aux 0 router(config-line)#password GeeksforGeeks router(config-line)#login
Assigning IP address to a router’s interface –
As we know router is a layer 3 device therefore every port of a router should have an IP address to work. By default, a router’s port has no IP address and its line protocol is also down.
router(config)#interface fa0/0 router(config-if)#ip address 192.168.1.1 255.255.255.0 router(config-if)#no shut
Here first we have to specify the router’s interface on which we want to give an IP address. Then we will enter interface mode where we will give an IP address as shown followed by its subnet mask (255.255.255.0).Then, we have made the router port administratively up by no shut command.
Copying and erasing configuration –
We can manually copy the running-configuration (configuration in RAM) to startup-configuration (configuration in NVRAM). Therefore, when the next time router will boot up, it will load the configuration that we have copied (as by default the configuration of NVRAM is loaded).
router#copy running-config startup-config
To erase the configuration of NVRAM, use the command
Attention reader! Don’t stop learning now. Get hold of all the important CS Theory concepts for SDE interviews with the CS Theory Course at a student-friendly price and become industry ready.
- Cisco Switch Configuration basic commands
- Hot Standby Router Protocol (HSRP) and Virtual Router Redundancy Protocol (VRRP)
- Backing up Cisco IOS Router image
- Cisco Router modes
- Network Devices (Hub, Repeater, Bridge, Switch, Router, Gateways and Brouter)
- Hot Standby Router Protocol (HSRP)
- Configuration of Router on a stick
- Introduction of Virtual Router Redundancy Protocol (VRRP) and its configuration
- Open shortest path first (OSPF) router roles and configuration
- Introduction of a Router
- Difference between Modem and Router
- Difference between Router and Switch
- Difference between Bridge and Router
- Difference between Router and Layer-3 Switch
- Difference between Router and Firewall
- Difference between Router and Gateway
- Difference between Router and Hub
- How to connect one router to another to expand the network?
- Network configuration and trouble shooting commands in Linux
- SMTP Commands
If you like GeeksforGeeks and would like to contribute, you can also write an article using contribute.geeksforgeeks.org or mail your article to firstname.lastname@example.org. See your article appearing on the GeeksforGeeks main page and help other Geeks.
Please Improve this article if you find anything incorrect by clicking on the "Improve Article" button below.