Channels can be defined as a pipes using which Goroutines communicate. Similar to water flows from one end to another in a pipe, data can be sent from one end and received from the another end using channels. By default channels are unbuffered, which states that they will only accept sends (chan <-) if there is a corresponding receive (<- chan) which are ready to receive the sent value. Buffered channels allows to accept a limited number of values without a corresponding receiver for those values. It is possible to create a channel with a buffe. Buffered channel are blocked only when the buffer is full. Similarly receiveing from a buffered channel are blocked only when the buffer will be empty.
Buffered channels can be created by passing an additional capacity parameter to the make( ) function which specifies the size of the buffer.
ch := make(chan type, capacity) // chan defines channel type
Here , capacity in the above syntax should be greater than 0 for a channel to have a buffer. The capacity for an unbuffered channel is 0 by default and hence it omit the capacity parameter.
Example 1 : Code to create a buffered channel.
geeksforgeeks geeksforgeeks world
Here in above code ,it is possible to write 2 strings into the channel without being blocked. It take 2 strings to the channel and does not block and print the result.
Example 2 : Program that write to buffered channel block.
successfully wrote 0 to ch successfully wrote 1 to ch read value 0 from ch successfully wrote 2 to ch read value 1 from ch successfully wrote 3 to ch read value 2 from ch read value 3 from ch
Here in above code the write Goroutine has a for loop which writes numbers from 0 to 3 to the ch channel. The capacity of this buffered channel is 2 and hence the write Goroutine will be able to write values 0 and 1 to the ch channel immediately and then it blocks until at least one value is read from ch channel as defined below :-
successfully wrote 0 to ch successfully wrote 1 to ch
After that, the read value and then sleeps for 2 seconds again and this cycle continues until the ch is closed. So the program will print the following lines after 2 seconds, as :-
read value 0 from ch successfully wrote 2 to ch
And this will continue until all values are written to the channel and it is closed in the write Goroutine.
Deadlocks in Buffered Golang Channel
It is defined as situation where the program during execution will result in fatal error due to panic at run time.
Here , in above code the write is blocked since the channel has exceeded its capacity and program reaches deadlock situation and print following message :
fatal error: all goroutines are asleep - deadlock! goroutine 1 [chan send]: main.main() /tmp/sandbox048494311/prog.go:11 +0x8d
- Channel in Golang
- Unidirectional Channel in Golang
- How to find the capacity of Channel, Pointer and Slice in Golang?
- How to find the Length of Channel, Pointer, Slice, String and Map in Golang?
- How to convert a slice of bytes in uppercase in Golang?
- Golang program that uses fallthrough keyword
- math.Lgamma() Function in Golang with Examples
- math.Float64bits() Function in Golang With Examples
- How to check equality of slices of bytes in Golang?
- atomic.AddInt64() Function in Golang With Examples
- atomic.StoreInt64() Function in Golang With Examples
- reflect.FieldByIndex() Function in Golang with Examples
- string.Contains Function in Golang with Examples
- bits.Sub() Function in Golang with Examples
- How to convert a slice of bytes in lowercase in Golang?
- io.PipeWriter.CloseWithError() Function in Golang with Examples
- Import in GoLang
- time.Round() Function in Golang With Examples
- How to add a method to struct type in Golang?
- Converting a string variable into Boolean, Integer or Float type in Golang
If you like GeeksforGeeks and would like to contribute, you can also write an article using contribute.geeksforgeeks.org or mail your article to email@example.com. See your article appearing on the GeeksforGeeks main page and help other Geeks.
Please Improve this article if you find anything incorrect by clicking on the "Improve Article" button below.