Open In App

Advantages and Disadvantages of Bus Topology

Improve
Improve
Like Article
Like
Save
Share
Report

In computer network there are various topologies available. A Bus Topology is one of them. All of the devices in a bus topology network are linked together by a single cable, which is referred to as a “bus” and the cable is known as backbone cable. All of the network’s devices can simultaneously receive the same signal due to the shared communication medium provided by this connection. In this article, we are going to discuss what is bus topology and its various applications, advantages, and disadvantages.

What is Bus Topology?

Bus topology carries transmitted data through the cable because data reaches each node, the node checks the destination address (MAC/IP address) to determine if it matches their address. If the address does not match with the node, the node does nothing more. But if the addresses of nodes match to addresses contained within the data then they process knowledge. In the bus, communication between nodes is done through a foremost network cable.

Bus Topology

Bus Topology

Key Features of Bus Topology

  • An efficient bus architecture is established, and each station is connected by a single backbone cable.
  • There are two requirements: Initially, the nodes are connected to the backbone cable directly, or they use a drop cable to help them connect.
  • The well-known access method for bus topologies is called CSMA (Carrier Sense Multiple Access).

Best Practice for Designing Bus Topology

  1. Plan for Scalability: Plan for the network’s future growth and expansion. Ensure that the bus topology can accommodate extra devices with out extensively affecting overall performance.
  2. Use Good Quality Cabling: Create a good cabling setup for the bus backbone. Ensure that the cable is properly shielded to minimize sign interference and degradation. Use cable with suitable bandwidth and make certain that it meets the necessities of the network.
  3. Implement Redundancy: Think about adding redundancy to decrease the risk of a single point of failure (SPoF).
  4. Terminate the Bus Properly: Terminate both ends of the bus with terminators to prevent signal reflection and ensure signal integrity. Improper termination can result in signal degradation and performance issues.

Advantages of Bus Topology

  • It is the easiest network topology for linearly connecting peripherals or computers.
  • It works very efficiently well when there is a small network.
  • The length of cable required is less than a star topology.
  • It is easy to connect or remove devices in this network without affecting any other device.
  • Very cost-effective as compared to other network topology i.e. mesh and star
  • It is easy to understand topology.
  • Easy to expand by joining the two cables together.

Disadvantages of Bus Topology

  • Bus topology is not good for large networks.
  • Identification of problems becomes difficult if the whole network goes down.
  • Troubleshooting individual device issues is very hard.
  • Need terminators are required at both ends of the main cable.
  • Additional devices slow the network down.
  • If the main cable is damaged, the whole network fails or splits into two.
  • Packet loss is high.
  • This network topology is very slow as compared to other topologies.

Applications of Bus Topology

  1. Local Area Networks (LANs): Bus topology was traditionally utilized in Ethernet LANs, mainly in older implementations wherein coaxial cables have been daisy-chained to connect computer systems.
  2. Industrial Control Systems: In industrial control system, bus topology is frequently used for connecting sensors, actuators, and different devices in distributed manipulate systems.
  3. Instrumentation Networks: Bus topology is appropriate for connecting devices, meters, and records acquisition gadgets in laboratory or commercial environments.
  4. Building Automation Systems: Bus topology is employed in building automation and HVAC (heating, ventilation, and air conditioning) structures to attach sensors, thermostats, actuators, and other manage devices.
  5. Telecommunications Networks: Bus topology has traditionally been utilized in telephone networks and early records transmission systems. However, it has largely been changed by using more superior topologies like mesh or ring for telecommunications applications because of higher fault tolerance and scalability.

Frequently Asked Question on Bus Topology – FAQs

What are the components of bus topology?

The major components of bus topology include backbone cable , terminator and droplines.

Is there a server in bus topology?

In a bus architecture, every node is directly connected to a single main cable. The network’s backbone is the primary cable. One of computer is work as a server from the network.

Is bus topology half-duplex or full- duplex?

Bus topology is half duplex.

What happens if two devices attempt to transmit data simultaneously in a bus network?

Data transfer in bus topology is accomplished by a procedure called “collision detection.” A signal sent by one device on the network is broadcast to all other devices in the network. When two devices attempt to transmit data simultaneously, there is a collision that results in distorted signals.


Last Updated : 01 Mar, 2024
Like Article
Save Article
Previous
Next
Share your thoughts in the comments
Similar Reads